Trailer Wiring Harness Installation - 1996 Mercury Grand Marquis- Video
Today on this 1996 Mercury Grand Marquee we're going to install part number 118326. This is a T1 vehicle wiring harness with four pull flat trailer connector from tow ready. Your first step is go ahead and open up the trunk. We need to remove the threshold right here because we need access to the liners that are covering up the back side of the tail lights. To remove our threshold, we need to go ahead and remove two plastic fasteners. I got a trim panel tool here, it works the best for this type of application. Kind of helps to start it from the bottom then work on the top side. more
12/22/2014 12:46:09 PM
Trailer Wiring Harness Installation - 2010 Mercury Milan- Video
Today on this 2010 Mercury Milan, we're going to install part number 118502 from Tow Ready. This is a T-One Vehicle Wiring Harness with a 4-Pole Flat Trailer Connector. Now when we need to use our wire harness, it's pretty easy, we'll go ahead and pull out just a little bit and shut the door on it. The door seal is thick enough where it won't hurt the wire. Now don't put it right here, otherwise you'll smash the wire. We'll go ahead and shut the hatch and then we can go ahead and pull out what we need out to our trailer. more
12/15/2014 2:55:29 PM
Trailer Wiring Harness Installation - 2008 Mercury Mariner- Video
Today on our 2008 Mercury Mariner we'll be installing the tow package wiring harness with four pole trailer connector from Draw-Tite, part number 118251. Now we'll be installing this in conjunction with the four terminal relays, part number TR38665. To being we'll go ahead and install our four pole harness. Underneath the vehicle here on the drivers side at the read bumper we'll go ahead and locate the factory plug here. Now we'll need to remove the covering from the plug so we'll go ahead and detach it from the body of the vehicle and unplug the harness. Now that we've exposed the plug we can take our new four pole and clip it into the plug here on our factory harness. more
2/1/2013 10:31:20 AM
Trailer Wiring Harness Installation - 1998 Mercury Villager- Video
Today on this 1998 Mercury Villager were going to install part number 118175KIT. This is a wiring harness that we have to hard wire to the vehicle. Go ahead and open the back hatch and get access to the wiring. There is a panel on the left hand side of the vehicle that well remove to get access to the wires. First well go ahead and remove the sheath to the wires that are going to the tail light on the left hand side. With the wires exposed well go ahead and unplug the wire harness from the tail light. more
11/6/2012 3:32:51 PM
Trailer Wiring Harness Installation - 2007 Mercury Mariner- Video
Today we are working on a 2007 Mercury Mariner; we are going to install a tow ready T-One Connector part number 118430. Our first step is going to be accessing the rear cargo door of the vehicle. We are going to remove the tail light assemblies, and there is two fasteners holding it on. Once you remove the two fastener screws, gently pull and pry the tail light assembly away from the vehicle as there are several locking tabs behind that hold the tail light in place. As you can see the locking tabs here. Now Im going to go ahead and disconnect the tail light wiring from the sockets. more
10/19/2011 12:10:36 PM
Trailer Wiring Harness Installation - 2002 Mercury Villager- Video
Ok, today we are working on a 2002 Mercury Villager. We are going to install part number 119175, T-one 4-pole wiring harness. I am going to go ahead to the inside of the vehicle and remove the side compartment door. You can see this also gives us access to our taillight wires and an area to mount our module. I am going to go ahead and repeat the same process on the passenger side of removing the cover. Ok, now that we have our cover doors opened up, what we are going to do is remove this trim panel piece so that we can route our wires from the driver side to the passenger side. Ok, now that we have our threshold piece removed, what we are going to do is take out this screw, or knob, which is a cargo hook, on the bottom and the top so that we can pull this panel away from the body of the vehicle to slide our wires underneath. You can see this will now give us plenty of access to feed our wires underneath the trim. 0:57 more
7/14/2011 12:34:22 PM
Trailer Wiring Harness Installation - 1997 Mercury Villager- Video
Today on this 1997 Mercury Villager we are going to install wiring harness part number 119175 from Tow Ready. We are going to wire up the harness mainly on the driver side of the vehicle. We are going to do these four wires and hook them up to the inside behind the taillight. And we are going to take our green wire and we are going to run it underneath the plastic to the other side to make our connection to the turn signal there. We will go ahead and temporarily take off the threshold here. This usually just pops right off. We are going to remove these doors, one on each side. Look behind the taillight and you will see the connection point with four wire going to it. Disconnect that and we can find our circuits for our converter box. And we are just going to peel away the electric tape so we have access to our wires. 0:50 more
3/4/2011 9:56:41 AM
Filter Videos
Filter Videos
